Les Forums

Les Forums

Les forums sont fermés. Ils restent présent pour consultation et archivage.
Vous pouvez désormais poser vos questions directement dans les commentaires en bas de chaque page du site.
Alors n'hésitez pas à participer

NM-CUE boot loader ne boot plus avec l'image de l'installer

Bonjour j'ai une nm-cue (unity express service engine dont je ne suis plus capable de remettre à zéro avec l'image installer. Quelqu'un a t il une idée ? Avez vous déjà tenté de faire un clone du drive du cue (avec un soft comme clonezilla par exmple) et de L,extraire sur le disque ?? voici mon out put :

Initializing memory. Please wait. 256 MB SDRAM detectedBIOS Version: SM 02.00BIOS Build date: 09/17/02System Now Booting ...Booting from flash..., please wait.[BOOT-ASM]Please enter '***' to change boot configuration: Found disk 0found 1 drivesroot cmd : root (hd0,0) Filesystem type is reiserfs, partition type 0x83kf: a1 : /bzImage root=/dev/hda1 ro plat=nmkf: a2 : /bzImage root=/dev/hda1 ro plat=nmin grub_open: /bzImage root=/dev/hda1 ro plat=nmin grub_open1: /bzImage root=/dev/hda1 ro plat=nmin grub_open2: /bzImage root=/dev/hda1 ro plat=nmin grub_open3: /bzImage root=/dev/hda1 ro plat=nm 1in grub_open4: /bzImage root=/dev/hda1 ro plat=nm kernel_func: kt: 0Unable to load imagein boot func: kt: 0Unable to boot imageøInitializing memory. Please wait. 256 MB SDRAM detectedBIOS Version: SM 02.00BIOS Build date: 09/17/02System Now Booting ...Booting from flash..., please wait.[BOOT-ASM]Please enter '***' to change boot configuration: *** ServicesEngine Bootloader Version : 2.1.14ServicesEngine boot-loader> config IP Address [192.168.1.250] > Subnet mask [255.255.255.0] > TFTP server [192.168.2.59] >172.16.2.59 Gateway [172.16.1.1] > Default Helper-file [cue-installer.nm-aim.3.2.2] > Ethernet interface [internal] > Default Boot [none|disk] [disk] > Default bootloader [primary|secondary] [primary] > Updating flash with bootloader configurationServicesEngine boot-loader> boot loader Invalid boot optionUsage: boot <disk | helper | diag | compactflash | chainloader>ServicesEngine boot-loader> boot helper nw_boot: 0 cue-installer.nm-aim.3.2.2Me: 192.168.1.250, Server: 172.16.2.59, Gateway: 172.16.1.1Loading cue-installer.nm-aim.3.2.2Dbg: Final image size: 11335004nm_get_bl_type: 0nm_load_cisco_chain_load: 0Debug: bl_sz: 94016Debug: cisco_bl_sz: 58641cisco_cl_addr: 0x1001730nm_get_bl_type: 0nm_load_cisco_chain_load: 0Debug: bl_sz: 94016Debug: cisco_bl_sz: 58641Debug: loader_sz: 4000loader_addr: 0x1200000Cisco BootLoader startverify_netboot_imgfound signatureFound bootableimg_start: b sig_len: 172 sig_start: lnm_get_bl_type: 0bl_sz: 94016Cisco_bl_sz: 58641after buf_len: 4000after KEY_InitMemreading key: 0reading key: 1reading key: 2reading key: 3reading key: 4reading key: 5after aesop_RSA_keyarray_readin verifysignature_md5, MD5 hash generated now, str format:hexmd5:715b5ff8414ab2b0b64780f287f9eef9Verifying signature now... calling RSA decrypt nowmem ptr: 0 704 832 968 1040 1172 1184 1196 1208 1220 1228 1244 1268 1284 1300 1316 1332 1344 1360 1384 1400 1664 1804 2080 2224 2364 2880 3396 3660 3924 4188 RSA decrypt returned:33verifysignature_md5, Orig MD5 hash generated during encryption:715b5ff8414ab2b0b64780f287f9eef9signatures match...Image signature verified successfullyCISCO_BL: boot_image: 0x1200000[LOADER]: image/plat/sz: 2/1/11335004Aesop Helper: system image header: v=2, b=946332, i=10386247Network boot: moving 3072 code bytes to 0x90000....Network boot: invoking kernel now[BOOT-PHASE2]: booting kernel[BOOT-PHASE2]: booting kernelLinux version 2.4.24 (bld_adm@bld-system) (gcc version 2.95.3 20010315 (release)) #1 Fri Mar 30 08:37:07 PST 2007Platform: nmsetup.c: handling flash window at [15MB..16MB]setup.c: handling kernel log buf at [250.5MB]setup.c: handling trace buf at [251MB]BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0800 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000000f00000 (usable) BIOS-e820: 0000000000f00000 - 0000000001000000 (reserved) BIOS-e820: 0000000001000000 - 000000000fa80000 (usable) BIOS-e820: 000000000fa80000 - 000000000fb00000 (reserved) BIOS-e820: 000000000fb00000 - 0000000010000000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)250MB LOWMEM available.On node 0 totalpages: 64128zone(0): 4096 pages.zone(1): 60032 pages.zone(2): 0 pages.DMI not present.Kernel command line: root=/dev/ram ramdisk_size=200000 ramdisk_start=0x6000000 console=ttyS0,9600n8 plat=nm Initializing CPU#0Detected 498.674 MHz processor.Calibrating delay loop... 996.14 BogoMIPSMemory: 239964k/256512k available (1211k kernel code, 15136k reserved, 693k data, 96k init, 0k highmem)kdb version 4.3 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reservedin atrace_initlog_head: h: -411752079, t: -1116901818, l: -39864027, w: 24708, s: -564133928Initializing trace bufferlog_head: h: -1426063360, t: 0, l: -318767104, w: 0, s: -1404044352Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)Inode cache hash table entries: 16384 (order: 5, 131072 bytes)Mount cache hash table entries: 512 (order: 0, 4096 bytes)Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)Page-cache hash table entries: 65536 (order: 6, 262144 bytes)CPU: L1 I cache: 16K, L1 D cache: 16KCPU: L2 cache: 256KCPU serial number disabled.CPU: Intel Pentium III (Coppermine) stepping 0aEnabling fast FPU save and restore... done.Enabling unmasked SIMD FPU exception support... done.Checking 'hlt' instruction... OK.POSIX conformance testing by UNIFIXPCI: PCI BIOS revision 2.10 entry at 0xeab9c, last bus=0PCI: Using configuration type 1PCI: Probing PCI hardwarePCI: Probing PCI hardware (bus 00)Limiting direct PCI/PCI transfers.Linux NET4.0 for Linux 2.4Based upon Swansea University Computer Society NET3.039Initializing RT netlink socketStarting kswapdkinoded startedVFS: Disk quotas vdquot_6.5.1devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)devfs: devfs_debug: 0x0devfs: boot_options: 0x1Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabledttyS00 at 0x03f8 (irq = 4) is a 16550AttyS01 at 0x02f8 (irq = 3) is a 16550ACisco ContentEngine Flash Driver Version 0.02RAMDISK driver initialized: 16 RAM disks of 200000K size 1024 blocksizeeepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.htmleepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and otherseth0: PCI device 8086:1229, 00:1A:E2:ED:16:E5, IRQ 9. Receiver lock-up bug exists -- enabling work-around. Board assembly 668081-002, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0x04f4518b). Receiver lock-up workaround activated.eth1: PCI device 8086:1229, 00:1A:E2:ED:16:E6, IRQ 10. Receiver lock-up bug exists -- enabling work-around. Board assembly 668081-002, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0x04f4518b). Receiver lock-up workaround activated.Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxPIIX4: IDE controller at PCI slot 00:07.1PIIX4: chipset revision 1PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:piohda: C/H/S=50127/232/176 from BIOS ignoredhdb: C/H/S=0/0/0 from BIOS ignoredhda: Hitachi HTE541680J9AT00, ATA DISK driveblk: queue c03210c0, I/O limit 4095Mb (mask 0xffffffff)ide0 at 0x1f0-0x1f7,0x3f6 on irq 14hda: attached ide-disk driver.hda: host protected area => 1hda: 156301488 sectors (80026 MB) w/7512KiB Cache, CHS=9729/255/63, UDMA(33)init unit number == 0Partition check: /dev/ide/host0/bus0/target0/lun0: p1Model == Hitachi HTE541680J9AT00Flash capacity == 156301488init unit number == 1IEEE 802.2 LLC for Linux 2.1 (c) 1996 Tim AlpaertsNET4: Linux TCP/IP 1.0 for NET4.0IP Protocols: ICMP, UDP, TCP, IGMPIP: routing cache hash table of 2048 buckets, 16KbytesTCP: Hash tables configured (established 16384 bind 16384)NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.RAMDISK: Compressed image found at block 100663296Freeing initrd memory: 10142k freedVFS: Mounted root (ext2 filesystem) readonly.Mounted devfs on /devInit drive controlFreeing unused kernel memory: 96k freedUnable to handle kernel paging request at virtual address 6d28f198 printing eip:c0123757*pde = 00000000Oops: 0000 CPU: 0EIP: 0010:[<c0123757>] Not taintedEFLAGS: 00010206EIP is at __find_lock_page_helper+0x23/0x6c [kernel]eax: c13c1d44 ebx: 6d28f190 ecx: 6d28f190 edx: 00000c37esi: 00000c37 edi: c13c1d44 ebp: c12bdd3c esp: c12bdd2cds: 0018 es: 0018 ss: 0018Process init (pid: 1, stackpage=c12bd000)Stack: 00000000 c699eb00 c13c1d44 6d28f190 c12bdd54 c01237fc 00000000 c699eb00 000061be cfa10f5c c12bdd8c c01b77a0 c13c1d44 00000c37 000001d0 00000000 c699eb00 000061be 00000400 00000000 00000000 00000c00 00000c37 c13c1d44 Call Trace: [<c01237fc>] find_or_create_page+0x44/0xfc [kernel] [<c01b77a0>] rd_blkdev_pagecache_IO+0xb8/0x1d0 [kernel] [<c01b78f8>] rd_make_request+0x40/0x84 [kernel] [<c01b61df>] generic_make_request+0x123/0x138 [kernel] [<c01b624c>] submit_bh+0x58/0xdc [kernel] [<c013273e>] block_read_full_page+0x22e/0x24c [kernel] [<c01232c1>] add_to_page_cache_unique+0x95/0xa0 [kernel] [<c0159755>] ext2_readpage+0x11/0x18 [kernel] [<c01593bc>] ext2_get_block+0x0/0x370 [kernel] [<c0123374>] page_cache_read+0xa8/0xc0 [kernel] [<c01233ba>] read_cluster_nonblocking+0x2e/0x48 [kernel] [<c0124a1d>] filemap_nopage+0x109/0x20c [kernel] [<c0121088>] do_no_page+0x48/0x1c0 [kernel] [<c0121250>] handle_mm_fault+0x50/0xb4 [kernel] [<c0110309>] do_page_fault+0x185/0x4b2 [kernel] [<c0110184>] do_page_fault+0x0/0x4b2 [kernel] [<c010d596>] old_mmap+0xea/0x124 [kernel] [<c0108c24>] error_code+0x34/0x40 [kernel]Code: 39 7b 08 75 f4 39 73 0c 75 ef 85 db 74 32 ff 43 14 31 c0 0f <0>Rebooting in 2 seconds...Initializing memory. Please wait. 256 MB SDRAM detectedBIOS Version: SM 02.00BIOS Build date: 09/17/02System Now Booting ...Booting from flash..., please wait.[BOOT-ASM]Please enter '***' to change boot configuration: